LED light pucks Kit Pureflare Smart Warning Light

SYNCHRONIZED RECHARGEABLE LED LIGHT PUCKS - PERFECT WARNING LIGHTING!

The Pureflare Smart Warning Light is a complete kit with six high-quality rechargeable light pucks. The pucks are automatically synchronized when they are connected to each other, so through one puck you can control the effect mode and switch the other pucks on/off. The pucks are delivered in a hardcase bag, which works great for both transporting and storing the pucks . The bag also charges all pucks at the same time. The kit contains both a mains adapter and a 12V cigarette adapter. The bag is designed to be able to load the pucks even with the lid closed.

The pucks sense their surroundings automatically, and based on that either the LEDs on the top or on the edges light up. If the puck is attached to the car roof, the diodes on the edges light up, and if it is placed at the back of the car, the diodes on the top side light up. However, this function can be turned off.

The light pucks are completely waterproof and basically impossible to break. The pucks also float in water, so they can be used to attract attention even at sea! Very long battery life, a full 72 hours on one charge. Warranty 12 months.

The light pucks have magnets at the bottom and can be attached to all magnetic surfaces. The power source is a modern li-ion battery that can withstand freezing temperatures. The pucks are designed to withstand heavy wear, they are completely waterproof and can even be run over by cars without damage.

The light pucks can be used as observation or safety lights for traffic management, observation lights on vehicles or in other ways in situations where you have to call the attention of road users. In addition to road construction, traffic management, police matters and other similar needs, it is also perfectly suited to associations or private use where observation or warning lights are needed.

Examples of areas of use

• Warning and safety lights in traffic
• Warning light on trailer or cart
• Traffic control
• Warning lights in the boat
• Fishing net marker light (waterproof)
• Warning lights at dive sites (floating)
• Toys for the kids!

Technical specification

• Power modes: 5 pcs
• Operating time: up to 72 h
• LED: 12 on the sides, 4 on top
• Protection class: IP67
• Outer dimensions: 108 x 92 x 30 mm
• The pucks are synchronized with each other automatically
• Warranty: 12 months

Power modes

• Steady flashing
• Medium fast blinking
• Slow flashing
• Double flashing
• Decreasing blinking

Quick guide

Turn on the light puck with a push of the switch. The light puck announces the remaining charge by flashing the red diodes (1-4 times depending on charge), after which the puck lights up. Scroll between the power modes with a push of the switch. Turn off the puck by holding down the switch for about 3 seconds.

The light puck announces the remaining charge by flashing the red diodes 1-4 times depending on the remaining charge. The flashes indicate the following:

• 4 flashes: over 75%
• 3 flashes: 50-75%
• 2 blinks: 25-50%
• 1 blink: below 25%

To synchronize one or more pucks, simply light them near each other. The pucks' power modes, switching on and off can now be controlled through a single puck. You can sync any number of pucks as long as they are within 15m of each other. If you want to make the pucks flash at the same rate, it is enough to quickly double-press the switch.

The pucks sense their surroundings automatically, and based on that either the LEDs on the top or on the edges light up. If the puck is attached to the car roof, the diodes on the edges light up, and if it is placed at the back of the car, the diodes on the top side light up. That function can be turned off by pressing the π button. On the first press, only the LEDs on the sides light up, on the second press, the diodes on top of the puck light up, and on the third press, the settings return to the automatic mode. If you want to turn off a puck without simultaneously turning off other synchronized pucks, press and hold the π button for 3 seconds.

Charge the pucks by placing them in the charging case, and connect the case to a power source using one of the included adapters. The charger's indicator glows green while charging is in progress, and turns red when the batteries are fully charged.